Step by Step Installation Instructions for One-person Sauna

Installation procedure

Sauna Room: 

1. Structure of Infrared Sauna. See FIG-1.                                                                                     

   FIG-1

2. One-person and two-person unit are packed into two cartons. See FIG-2.                                                                                                                 

   FIG-2 Two cartons	FIG-2.1 C/No.

   
   
3. Make sure all parts are present before installing the unit. See packing list below.
   A. User manual   B. Bottom board      C. Back Board     D. Left side board   E. Right side board   F. Sitting baffles    G. Sitting board      H. Backrest       I. Front board      J. Internal top board  K. External top board   L. CD Player    M. CD player back cover    N. Screwdriver    O.  Towel shelf
4. Place the bottom board (section 4, Sauna room diagram, p.3) in the desired location of your sauna, and make sure which side is the front and which side is the back. See FIG-3.                                                                                                                  

   FIG-3 Placing bottom floor	FIG-4 Assembling back board

5. Align the backboard with bottom board’s corresponding battens; make sure they are in line. See FIG-4.
6. Align the left board with bottom board’s corresponding battens; make sure left board fits flush into backboard. See FIG-5.                                                                                                       

   FIG-5 Assembling left board	FIG-6 Latching

7. The latch has a guide tab that must be placed in the guide slot for alignment. Pick up the back panel (hold it upright to the floor panel) and place the tab in the slot, do not latch at this time. When the back wall and the front wall/side wall are set together on the floor panel, close and latch it. See Figure 6.
8. Align the right board with bottom board’s corresponding battens; make sure right board fits flush into backboard and latch together. FIG-7                                                                                                       
   

   FIG-7 Assembling right board	FIG-8 Assembling sitting board's support

9. Slide the sitting baffle down vertically into the slot within left and right panel. Next, connect the bench’s heater element wire to corresponding wire from the back wall, then locate sitting baffle and slide into place.  See FIG-8,9  Note: Make sure the wires are connected tightly, otherwise the heater will not work.                                                                                                                 

   FIG-9 Connecting wire	FIG-10 Assembling sitting board

10. 10. Put the sitting board horizontally on corresponding battens of the backboard. See FIG-10
11. Screw the backrest onto the backboard. (Section 12)   See FIG-11.                                                                                                                 

    FIG-11 Assembling sitting board	FIG-12 Assembling front board

12. Align the front board (Section 3) with bottom board’s corresponding battens, and then latch it with the left and right boards respectively. Notes: Take caution of the glass door to avoid damage. See FIG-12.
13. Put the wires of front board and backboard into the cabinet to avoid pressing the wires during installing. See FIG-13. Open the door, raise the top board high enough to see if it fits with the surrounding boards, then put down.                                                                                                       
    

    FIG-13 Setting the top board	FIG-14 Leading the wires of heaters onto the board through the corresponding hole

14. During the course of putting down the internal top board, make sure all the wires (mentioned above) and connecting plugs are slipped through the corresponding holes of the top board. All these wires will be led into connecting with the controller on the internal top board. See FIG-14.
15. See FIG-15. Connect all the wires and connectors to the corresponding outlets on the top board. Please be sure all the plugs are connected tightly.                                                                                                                 

    FIG-15 Connectors on the internal top board	FIG-16 Put down the wires into the sauna cabin

16. After that, put down the power plugs of the speakers, temperature sensor, control panel and CD player through the hole near the fan on the top board. See FIG 16.
17. Take out the car stereo with CD player (section 2), check its spare parts, put the stereo into the CD frame. See FIG-17.1. Then screw the attached stereo support to the stereo. See FIG-17, 17.1, 172, 17.3 Note: CD player on selected model only.                                                                                                                                                     

    FIG-17	FIG-17.1 Fixing stereo w/ CD
    FIG-17.2 Fix the CD to the metal support	FIG-17.3 Lock the CD with its metal support

18. All the wirings from top board should be linked with corresponding connectors of the control panel, the CD player, the temperature sensor and the radio antenna. Otherwise, the sauna will not function if any connections are missed. See FIG 18-21.                                                                                                                                                                                                                       
    

    FIG-18 Link the CD connectors	FIG-19 Link the sensor connectors
    FIG-20 Link the control panel connectors	FIG-21 Link the antenna connectors
    FIG-22 CD player back cover and screws	FIG-22.1 Fix the CD player back cover with screws

19. Take down the bag of screws affixed to the CD player back cover; use a cross screwdriver to screw in the CD player back cover over the CD player. See FIG-22, 22.1.
20. Making sure all steps are finished correctly, plug in the power and try using the sauna at first to make sure it will work properly. Then put the external top board (section 10) over the internal top board, and take out the power plug through the corresponding hole in the external top board. See FIG-23.                                                                                                                 

    FIG-23 Slip the power plug through external top board	FIG-24 Fix the external board with screws

21. Take the screws affixed on the external top board, then set up the board using the cross screwdriver. See FIG-24.
22. Installation Completed.

User Tips ? Add tips